Playstation 4 Motherboard Austausch

Geschrieben von: Sam Omiotek
  • Kommentare: 65
Playstation 4 Motherboard Austausch

Schwierigkeitsgrad

Mittel

Schritte

21

Zeitaufwand

10 Minuten

Einleitung

Sofern Probleme mit der Hauptplatine auftreten, ist hier eine Anleitung wie diese auszutauschen ist. Bitte beachten, dass dabei die Garantie des Herstellers erlischt.

  1. iEw34r6UEPlfvDAG

    • Drehe die PS4 so, dass der Boden nach oben zeigt und die Anschlüsse auf deiner Seite liegen.

  2. nQ1FQm4txAICMXbs
    nQ1FQm4txAICMXbs
    EK1TODlCVeFiLJt3

    • Entferne die beiden Garantieaufkleber vorsichtig mit einem Schraubendreher.

    • Achtung: Bei entfernen oder beschädigen der Garantieaufkleber erlischt die Garantie des Herstellers.

    Not true, removing stickers can’t void warranty as that’s illegal.

    Keyser Soze -

    Io però al di dietro ho solo 2 viti, quelle centrali. Come faccio?

    manuel gentili -

  3. PRXVWUDJLgaTIKqf

    • Löse die vier 9mm TR9 Torx Security Schrauben auf der Rückseite der PS4.

    Depending on the model of PS4, (i.e. CHU-1001A vs. CHU-1215A) it may only have the two screws in the center, not the edge ones.

    Sawyer Coe -

    In den Werkzeugen sind:

    Werkzeuge

    Pinzette

    TR8 Torx Security Screwdriver

    Spudger

    Phillips #0 Screwdriver

    Compressed Air

    aufgeführt, bei diesem Schritt wird von einem TR9 gesprochen, wird dieser benötigt und wurde in der Werkzeugliste vergessen oder ist es ein Tippfehler?

    Robert Oktabec -

  4. N3CPcTv3CKuNteDm

    • Entferne die Unterseite der PS4 von dem Hauptteil. Hierzu einfach die hintere Seite anheben und vorsichtig nach oben und vorne drücken.

    This can be extremely tricky to do. Some force is needed and if using a tool to pry it open (and this might very well be necessary) you risk damaging or breaking the plastic. Just take your time and be mindfull of where you place your pry tools.

    Joakim Johansson -

    Found a video that shows how to do it when it’xs only two screws

    https://youtu.be/yTunkv7688c?t=42

    Frida Svanberg -

  5. 15rDZS3s3xkASeCN

    • Entferne die drei 9 mm TR9 Torx Security Schrauben des Netzteils.

    • Entferne die beiden 4 mm Kreuzschlitzschrauben #1.

    It looks like that for CUH 1216A model, security TR8 and PH0 fits better

    sartoric -

  6. PuJcoIcSteWubwtk
    PuJcoIcSteWubwtk
    wCFpNhCgmN2IDJjM

    • Trenne den Netzstecker von der internen Stromversorgung.

    • Hebe das Netzteil an, um es aus dem Gehäuse zu entfernen.

    you need to lift the power board/box up vertically first as there are 2 long prongs extending up into the box. if you try to lift just one end you will bend the prongs.

    pollytintop -

    has anyone used any of these guys, i don't fancy doing it

    http://www.trustedrepairs.co.uk/electron...

    Damian -

    during this step it exposes a black phillips head screw at least on some models(such as mine) this screw mates the metal sandwich around the motherboard together. I was unable to perform step 19 until I released this Black short Phillips screw.

    gfinch1 -

    I just came across this screw at the same time. It is extremely stuck and I'm afraid to strip it. Any ideas?

    Richard Maya -

    The picture shows the power supply connector being removed from the main board instead of the power supply. This conflicts with the instructions which are correct given how it was most likely put together.

    Clay W -

    This is a poor instruction. Obviously you need to lift the psu out first but on my white ps4 it simply won't budge on one side. Now I'm stuck already.

    Rainer De Temple -

    Rainer, look at pollytintop’c comment. Lift vertically and you will get to next step. I used a screwdriver on the side opposite the fan, but I am a savage in many ways. If you insist on treating it delicately a small suction or powerful tape might work.

    We may not all make it back. Good luck

    Mello -

    Guten Tag,

    an dem Mainboard meiner PS4 ist die Buchse mit den Metallstücken drin, wo man den Stecker des Netzteils reinsteckt, abgebrochen. Als ich das Netzteil rausnehmen wollte, habe ich viel zu fest gezogen und nun ist es ab.

    Bilder: https://imgur.com/a/hIMeWTh

    Welche Methoden gäbe es dieses Problem zu beheben?

    Mit freundlichen Grüßen

    JotEssYT -

    It feels very stuck, but if you can just get the “more" stuck end up a little first (I gently used a screwdriver as a skinny finger) and hold it there with your real fingers, you can get the easier side up a little too, then lift both together simultaneously with your hands. (1001a model, here)

    Mr. Porter -

    Tip is to turn it upside down n gently wiggle the weight of it will bring it out

    Chicky Boy3 -

    the only way I found to unplug this was to have tweezers holding down the outer connector, then using your fingers to pull firmly but gently on the wires close to the connector, with some wiggling

    noah.mooresmith -

  7. prMqSOonRco2BtHA
    prMqSOonRco2BtHA
    sQspFjHwJ56hgmqp

    • Trenne den Flachdraht vom optischen Laufwerk, indem du auf den Metallbügel drückst und vorsichtig am Draht ziehst. Dies sollte nicht viel Kraft erfordern.

    • Trenne denselben Flachdraht vom Motherboard. Achte darauf, den Metallbügel zu drücken und den Flachdraht vorsichtig zu lösen.

    If your PS4 eject button doesn’t respond/work and it doesn’t accept discs ( it doesn’t beep or nothing happens when you touch the eject button and it doesn’t make noise when you try to put a disc in and doesn’t take it) it could be because you took the wire ribbon out the optical drive or motherboard the wrong way and did not press down on the metal tab. ( like I did ) the wire ribbon should have these tiny “wings” on both sides and on both ends. Easy and very cheap fix. Ordered a new ribbon wire on amazon for $12!!! Better then buying a new PS4!!!!

    manny730 -

    Any way to get one of those wings out ? One of them broke off as I was pulling the cable out and is stuck.

    Luke Griffiths -

    Attention, pour sortir la nappe de connection du lecteur optique, il faut appuyer sur la lame métallique du connecteur avant de tirer sur la nappe, c’est un verrou.

    LOPAT -

    Just to emphasize, these are called ZIF cables, or “zero insertion force".

    Truly, you only need to press on the metal button and pull gently *straight* out. No wiggling. No yanking. There is no click.

    If you're putting it back in, the clip “clicks" into place by popping back up.

    Mr. Porter -

    Anyone knows how to remove the broken piece of ribbon stuck inside the connector?

    Sergio Colman -

  8. 6GghfvK6T2yA6bFX

    • Ziehe das Netzkabel vom Motherboard ab.

    Wo geht das andere Ende vom Kabel hin???

    tuure seeger -

    Wo endet das Kabel. Wo kommt die andere Seite hin. Finde kein Anschluss

    tuure seeger -

  9. DnCI3GZ3SI5crQWi

    • Entferne das Wlan-Kabel vom Motherboard.

  10. eRwsqkJnLnJiLN1T

    • Entferne die vier 9 mm Torx Security TR9 Schrauben.

    • Entferne die 5 mm Kreuzschlitz #1 Schraube.

    Mine on the bottom right near the board was a 5mm Phillips #1 instead of the expected 9mm Torx screw. Also, I have a shield plate covering my (or my customer's) board here.

    CPR Matthews, NC -

    Mine is the same

    Jesse King -

    Model Cuh1001a

    Jesse King -

    the guide has missed the optical drive shield. DO NOT PROCEED WITHOUT REMOVING IT. the “optical drive cord “ must be removed from the drive to continue.

    Max R. -

    This guide does not explain how to remove the metal plate on top of this board.

    Nicola Centrone -

  11. cHrbCaoAJTFxAhG3

    • Entferne die Wlan-Antenne.

  12. d5lUsMW4JDUBKKPA

    • Hebe das optische Laufwerk an und entferne es aus dem Gehäuse.

  13. OVFRUrmYbQoZgswO

    • Drehe das Gerät um und entferne die linke obere Platte, indem du es zurückdrückst und anhebst.

  14. wGo5oPEUGS4wSjQa

    • Entferne die beiden 9 mm Torx Security TR9 Schrauben.

    • Entferne die 5 mm Kreuzschlitz #1 Schraube.

  15. 1JnayMvJxA64V1Q5

    • Ziehe an der Festplatte und entferne diese aus dem Gehäuse.

  16. JQRvloDTr12PLnos

    • Hebe die Vorderseite der oberen Abdeckung an und schiebe sie nach hinten.

    my right corner, by the ps4 logo, was VERY snug, it took me a few minutes to pop that corner off, took a decent amount of force to pop it off

    chris -

    we used the screwdriver to pry it open in the corner

    Sabrina Shahid -

    I try being extremely gentle when working with electronics, but you need a tad more force this. Perhaps you'll need the same force for pulling those miles cables for the optical drive earlier. :)

    Mr. Porter -

  17. EBUQhwZuVjrEwJg1

    • Entferne die zwölf 9 mm Torx Security TR9 Schrauben.

    There’s a black Phillips screw next to the power supply connector that needs removed before removing the metal cover.

    louhobby -

  18. mxVfMbkaEf1GWU1S
    mxVfMbkaEf1GWU1S
    YhQbfrYYyEGABawj

    • Entferne die beiden 9 mm Kreuzschlitz #1 Schrauben.

    • Entferne die Metallhalterung.

    Danach muss auf der Innenseite noch eine schwarze Schraube gelöst werden, sonst kann man die Abdeckung und auch nicht Mainboard lösen.

    Maik Heidemann -

  19. iZCMVVFpohy5qf2Z

    • Hebe die Metallabdeckung an und entferne sie.

    On some PS4 consoles there is a small black Phillips head screw under the PSU securing the metal cover to the midframe of the console. If you do not remove this screw you will not be able to remove the metal cover, and run the risk of damaging it, or the motherboard.

    Jordan Troxel -

  20. hDQaYiXgCke3M1pR
    hDQaYiXgCke3M1pR
    5LZbWfygWRQpTFJp

    • Trenne den 3-adrigen Stecker vom Motherboard, indem du ihn vorsichtig nach oben und weg vom Motherboard bewegst.

    What can i do if i broke these three little prongs?

    Josh Turner -

    2 options 1 make a new contact, 2 buy a New fan as it is The fan contact ;)

    Karl eriksson -

    Which kind of connector is this?

    robbitara -

    Hab meine Halterung auch Abgebrochen.

    Das Komplette “ding” ist vom Mainboard/PCB Abgebrochen…

    Was kann man tun?

    Cem Ce -

    Hab meine Halterung auch Abgebrochen.

    Das Komplette “ding” ist vom Mainboard/PCB Abgebrochen…

    Was kann man tun?

    Georgios -

    I accidentally pulled the little red cord out from the white casings. Can I shove it back or do I need a new fan?

    Hobocop -

    Place one side of tweezers under from wire side, pinch with tweezers, and use to lift up, this pulls the wire out of the lock. (They aren't pins inside, but fins.)

    Mr. Porter -

    Having no patience I pulled all 3 fan wires out of connector on motherboard but all wires have there metal connector tips so can I put back into motherboard or did i ruin my fan

    asmar wash -

    Please be EXTREMELY careful, as it is exceedingly easy to break that connector. ☹️

    Except, of course, if you actually plan to replace the fan anyway, well, a new connector comes with the fan, so just look out for the motherboard part of it.

    Wolfgang Bachmann -

    Help!! Si è staccato il connettore dalla scheda madre come lo riattacco????

    Grazie

    Emanuele Lucidi -

    Liebe Gemeinde, leider kann ich die 3 Kabel (braun/schwarz/grau) nicht mehr an das Motherboard anbringen. Ich möchte deswegen den Lüfter an ein externes Netzteil anschließen. Dazu müsste ich wissen für welchenZweck die drei unterschiedlichen Kabel sind,… Masse, Stromzuführung mit wieviel Volt etc.,… schwarz ist…. // braun ist … // grau ist … Bitte schreibt mir auf michel@richterle.de ….. das wäre sehr nett, liebe Grüße

    Michael Richter

    Michael Richter -

  21. dRKkBpjjETBIZYVA

    • Hebe das Motherboard an und entferne es aus dem Gehäuse.

    • Das Entfernen des Motherboards löst die Wärmeleitpaste zwischen dem Prozessor und dem Kühlkörper. Bevor du dein Gerät wieder zusammenbaust, trage neue Wärmeleitpaste auf: Folge dieser Anleitung, um zu erfahren, wie das geht.

    Unfortunately it costs more for the motherboard and optical drive together than it costs for a new PS4 1TB with a game

    Blake Hannan -

    Was passiert wenn man das nicht macht?

    Und was passiert mit der ps4 ohne Wärmeleitpaste ich hab nämlich meine ps4 geöffnet und die Wärmeleitpaste abgewischt und ich habe es zusammen gebaut und die ps4 piept nur 3 mal und geht aus.

    Könnt ihr mir Helfen?

    danke shirin -

    @danke shirin die gleiche hat zu mir passiert. It also happened to me, I did this tutorial and put everything back together, and now it beeps three times red and goes off. I used paste but I guess it is because of sth else

    anonymous 2356 -

    ASLAMULAIKOM sir me Pakistan ho. Mujhy. English. Nahi ati. Mera. PS4 karan hai. Maine. Sab kuch. Khul diya hai plz Mera. PS4 sahi karsaakhty

    Shoaib Mirza -

Abschluss

Arbeite die Schritte in umgekehrter Reihenfolge ab, um dein Gerät wieder zusammenzubauen.

Tinte & Feder

Sam Omiotek

Mitglied seit: 25/02/19

41564 Reputation

14 Kommentare

Regarding the three wire plug in step 20 - is there a good way to repair this piece if, say, you pulled the wires out of the connector by accident? is there a place to get a replacement part?

Ryan Statz -

PlayStation 4 (CUH-10XXA and CUH-11XXA) Fan

ERI Employee -

I have tried to replace the hdmi port however being somewhat of an idiot I slipped and knocked off onto the little black squares just behind the port on the left hand side. Does anyone know what these are?

Geoff Parker -

contacts of the motherboard

lillarrypimp1993 -

You may be talking about capacitors that are critically important for the unit to function.

South30 -

You mean that little brown parts next to the desoldered HDMI port chip? Seems to be capaciators.

Check it with a multimeter: No connection through that parts: Capaciator, Connection through that parts: Coil

http://www.fingers-welt.de/imghost/up/20...

Sebastian Coenen -

Ok so I was taking mine apart, and while I was separating the ribbon wire from the optical drive during step 7, I broke the top off the connector by accident. I thought I could fix it with hot glue, but my ps4 doesn't read disks (at all, doesn't even know there's a disk in the drive). Is there a way to repair this without getting a new drive?

jonathanhart54 -

when I bought the replacement motherboard and optical drive and installed everything, I got a message saying connect USB with software update. Is this because I'm using my original hdd from my original mobo+ optical drive that is different from the hdd my replacement parts came with?

Quaymetsu -

Could you please tell me where you bought a replacement motherboard from as i've been looking everywhere!?

Roger flaps -

You cannot just replace the motherboard on a PS4. The motherboard is married to the logic board on the blu-ray drive. Swapping the motherboard without carrying over the original logic board will render the drive useless.

Will -

I’ve read along the guides that a BDP-020 optical drive can work with an SAA-001 motherboard, but mine still receives the CE-35888-2 error. Am I replacing the incorrect part?

Cristian Nickles -

Hi my ps4 has stopped working and doesnt turn on at all, ive tried different outlets and different power cables for the ps4, still no luck. Ive pulled it apart and had a look at the power supply board and mother board aswell as dusted it all out. The mother board has yellow stains/ dots near the hdmi port and some other random spots around the mother board. I have the first ps4.

Does anyone know whats wrong? Id rather fix it than pay for a new one.

Jared Breen -

Habe mall eine frage habe meine sauber gemacht die ps4.und jetzt geht die kurz an und wieder aus was kann ich machen jetzt

dst11 -

Hi all, I am facing this CE-34878-0 error on all games. Reinstalled the software, replaced the HDD and reinstalled latest software but this error is keep coming. What is the solution.

Salman Hameed -