Dyson Ball Animal Bürstenleiste tauschen

Geschrieben von: Mairead Nye
  • Kommentare: 10
Dyson Ball Animal Bürstenleiste tauschen

Schwierigkeitsgrad

Einfach

Schritte

8

Zeitaufwand

5 Minuten

Einleitung

Dies ist eine Anleitung zum Entfernen der Bürstenleiste zum Ersetzen oder Reinigen.

  1. RoTO3eHhArUEbWny
    RoTO3eHhArUEbWny
    VcrgxisR6vBBxiMQ

    • Schalte den Staubsauger aus und trenne ihn vom Stromnetz.

  2. U3SKEQRKlBjZDkG5
    U3SKEQRKlBjZDkG5
    FW6YStYOQmHsyjpQ

    • Lege den Staubsauger auf den Rücken und stelle die Bürstenleiste nach oben.

  3. Ztgkf5B5LdBx2YwQ
    Ztgkf5B5LdBx2YwQ
    gxDsSqh5X2ioZ1lT

    • Ziehe den roten Ring unten am Bürstenkopf nach unten und der Bürste weg.

  4. 4dPbXJ4rg61GMIWl

    • Ziehe die Bürstenleiste aus dem Staubsauger heraus.

  5. oxEGwKoXBMSLhHTR

    • Ziehe die roten Laschen auf der Oberseite der Bürstenleiste ab.

  6. ARMkSdAPdVhRYqQi

    • Entferne die Frontblende der Bürstenleiste.

  7. T2LdFbRMWqBtu4Bm
    T2LdFbRMWqBtu4Bm
    wxwYMlXIcrWRND51
    F5AokBbBpBrWu41R

    • Entferne die vier Schrauben mit einem Torx T10 Schraubendreher.

    On mine, these 4 screws don’t take a Torx T10 bit but a regular phillips.

    John Vannoy -

  8. wOPXcvKoAS1MAReQ
    wOPXcvKoAS1MAReQ
    P3rlJy3FWXlMLreW

    • Hebe die Bürstenleiste vom Gehäuse weg, während du sie gleichzeitig zur Seite ziehst.

    • Es braucht eventuell etwas Wackeln und Kraft.

    Thanks for the instructions. They were a great help. However, after reassembling, the short brushbar is not rotating when the vacuum is turned on. Only the long brusbar is rotating. Any idea why?

    (The short brushbar spins freely)

    Charles Woodring -

    Thanks so much for posting. My head had become a little bit grungy and was trying to find a way to clean it. In the model I have the rings and clips are gray. Maybe they changed them to “match” the color scheme. Either way you’re amazing and thanks again!!!!!

    Paulie Keener -

    Is there a way to get the motor apart with the little wheel mine is clogged with dirt

    Dawna Wolf -

Abschluss

Befolge diese Anweisungen in umgekehrter Reihenfolge, um dein Gerät wieder zusammenzubauen.

Tinte & Feder

Mairead Nye

Mitglied seit: 08/05/17

351 Reputation

6 Kommentare

I'm like to know if this works for the Dyson ball animal2 as well

Jean Riehle -

It does work

ade 23 -

We used this guide to clean the brushbar assembly of the DC41 animal too. Thank you SO MUCH for writing it!!! We’d never have tried pulling the bar off sideways.

Anthony Clark -

Thanks to MaireadNye for the easy to follow guide. I used this to remove and clean the brush bar and its housing on a Dyson Animal 2 upright vacuum. The four screws securing the brush bar were not T10 Torx, but rather Phillips head, so no big deal. What took the longest amount of time was searching for my Torx tools before I began, which is unlike me. I usually grab tools as I go, but since only one was required, I decided to (unnecessarily) have it ready to go. I used vinegar first to get out a soy sauce type smell, but dish soap was what worked. Thanks again!

(And thanks to Dyson for making stuff like this user-friendly!)

renee marie -

what is the part and part number of the wheel in between the brush bar?

Jerry Taylor -

After you get the 2 brush bars out, I highly recommend removing the black plastic part from the end of each one (remove the single torx screw in the center). On mine, there was a lot of hair and dust trapped underneath that piece, that was keeping it from rotating freely. One of them was noticeably hard to rotate, until I cleaned that stuff out, and then it rotated normally.

John Vannoy -