Bissell SpotBot Pet Repair Brush Motor Replacement

Geschrieben von: Anthony Bonvino
  • Kommentare: 1
Bissell SpotBot Pet Repair Brush Motor Replacement

Schwierigkeitsgrad

Moderate

Schritte

11

Zeitaufwand

30 Minuten - 1 Stunde

Einleitung

This replacement guide will cover how to replace the brush motor on the Bissell SpotBot Pet carpet cleaner.

  1. BIoxqyLwqbhwAXtm

    • Set your Bissell SpotBot Pet on a flat surface to begin your repair.

  2. onWbifIpYI1LukKQ

    • Lift straight up on the right container to remove it from the vacuum.

  3. uhFpoHPIsq4QkS5b
    uhFpoHPIsq4QkS5b
    PZFrSi2rjtMiINIS

    • Lift up on the tab on the top of the vacuum and then lift straight up on the left container to remove it.

  4. m2Uo1xlcI6UHQiXo

    • Remove the vacuum tube by sliding it out of its holder on the side.

  5. 1c2DjKgCSKXWucbg
    1c2DjKgCSKXWucbg
    QNrGfmDvdkWeMhsh

    • Unscrew the 4 screws on the top of the device and gently lift the top half up.

    • A ribbon cable is still attached to the underside of the top half.

  6. UCAIpJyAQOLexGAU
    UCAIpJyAQOLexGAU
    sRFx4aD36H4MDlqH
    ANHEgvy3HIy3aFKo

    • Unplug the ribbon cable connecting the bottom half to the control panel on the top half. Set the top off to the side.

  7. WKZmtLaCCOILHOJT
    WKZmtLaCCOILHOJT
    KonVcDD22bhwrMNG

    • Unscrew the screw next to the white plastic wiring harness box. This will allow you to set the box off to the side.

  8. kwMIXGYTypIMtIdp

    • Unscrew the screws on the plastic holder on the right side of the device. Remove the plastic holder from the vacuum.

    • Unscrew the screws that mount the vacuum motor to the device

  9. 3VySQNNcBXHJK2na
    3VySQNNcBXHJK2na
    MhbuosjFE6DTCLyf

    • Unplug the wires connecting the motor to the wiring harness.

  10. 2jGMsxGJSNVSNROD
    2jGMsxGJSNVSNROD
    v6I4JYdOQZYQxPZT

    • Lift the white suction motor from the right side of the device. Lift it straight up and set it off to the side of the vacuum.

  11. 5YRYL2r3ZPCK3JbF
    5YRYL2r3ZPCK3JbF
    VFrnNn65owfb1LmC

    • Remove the screws for the brush motor. This motor controls the automatic scrubbing mechanism.

Abschluss

To reassemble your device, follow these instructions in reverse order.

Tinte & Feder

Anthony Bonvino

Mitglied seit: 27/09/17

437 Reputation

Ein Kommentar

hi i think you did an amazing job of breaking down how to disasemble this spotbot. i have the exact same one and though it works great suction is amazing, the brushes dont spin and i took it apart completely except i didnt know where the motor was that controlled the brushes until reading this. thanks so much

art -